DLTUK65 series-Solid core rods

Literal statement:
The round rods of this type is suitable for finishing difficult-to-cut materials, like quenched steel, HSS and composite materials. End mills and PCB bits are recommended.

Regular size:

Ordering code	Diameter (mm)	Tolerance (mm)	h6 (mm)	Length (mm)	Tolerance (mm)
DLTUK65-A-012330	1.2	0～+0.2	1.0	330	0～+1.5
DLTUK65-A-022330	2.2	0～+0.2	2.0	330	0～+1.5
DLTUK65-A-032330	3.2	0～+0.2	3.0	330	0～+1.5
DLTUK65-A-042330	4.2	0～+0.2	4.0	330	0～+1.5
DLTUK65-A-052330	5.2	0～+0.2	5.0	330	0～+1.5
DLTUK65-A-062330	6.2	0～+0.2	6.0	330	0～+1.5
DLTUK65-A-072330	7.2	0～+0.2	7.0	330	0～+1.5
DLTUK65-A-082330	8.2	0～+0.3	8.0	330	0～+1.5
DLTUK65-A-092330	9.2	0～+0.3	9.0	330	0～+1.5
DLTUK65-A-102330	10.2	0～+0.3	10.0	330	0～+1.5
DLTUK65-A-112330	11.2	0～+0.3	11.0	330	0～+1.5
DLTUK65-A-122330	12.2	0～+0.3	12.0	330	0～+1.5
DLTUK65-A-132330	13.2	0～+0.3	13.0	330	0～+1.5
DLTUK65-A-142330	14.2	0～+0.3	14.0	330	0～+1.5
DLTUK65-A-152330	15.2	0～+0.3	15.0	330	0～+1.5
DLTUK65-A-162330	16.2	0～+0.4	16.0	330	0～+1.5
DLTUK65-A-172330	17.2	0～+0.4	17.0	330	0～+1.5
DLTUK65-A-182330	18.2	0～+0.4	18.0	330	0～+1.5
DLTUK65-A-192330	19.2	0～+0.4	19.0	330	0～+1.5
DLTUK65-A-202330	20.2	0～+0.5	20.0	330	0～+1.5
DLTUK65-A-212330	21.2	0～+0.5	21.0	330	0～+1.5
DLTUK65-A-242330	24.2	0～+0.5	24.0	330	0～+1.5
DLTUK65-A-252330	25.2	0～+0.5	25.0	330	0～+1.5
DLTUK65-A-262330	26.2	0～+0.5	26.0	330	0～+1.5
DLTUK65-A-272330	27.2	0～+0.5	27.0	330	0～+1.5
DLTUK65-A-282330	28.2	0～+0.5	28.0	330	0～+1.5
DLTUK65-A-292330	29.2	0～+0.5	29.0	330	0～+1.5
DLTUK65-A-302330	30.2	0～+0.5	30.0	330	0～+1.5

Material composition:

1.Physical Properties:

A) Hardness greater than or equal to 94HRA；

B) Density greater than or equal to 14.6 g/cm³；

C) TRS greater than or equal to 4100 N/mm²；

D) Free of ETA phase condition；

E) No contamination by other materials；

F) Porosity = A00 / B00 / C00 ；

G) Uniform and consistent grain size. No grain size can be larger than specified.

H) Chromium carbide grain growth inhibitor only.

2.All the production, coatings are used in Germany, Switzerland, processing equipment；

3.It's proposed cutting less than 65HRC;

Advantage:
1、The factory use the advanced spray drying tower, HIP low pressure fritting furnace.
2、We have independent research team, from tool materials research and development, cutting tool design to tool application, and we also have the ability to provide customers with a complete set of product design program.

Surface roughness of rods: